Skip to main content

Doing a Jig

One of my hobbies is beekeeping. Unfortunately it is quite expensive to buy all the wooden-ware needed. As a result I decided to make my own hive bodies. But the problem is pushing a 2 x 10 of any length through the table saw and keeping a straight edge is challenging. I was talking with a workmate who recommended making a jig and using my circular saw. So this is what I came up with:
The base is a piece of 1/2 inch plywood about 12" x 12". There are 2 1 x scraps of wood on the sides sized to the 1 x 10 that hold it when the saw is pushed through. The top is another piece of plywood that is screwed down. Now I use the edge of this to piece of plywood as the guide for the circular saw.








So I force the 1 x 10 as far back into the jig as possible and it is the right size for the long ends of the hive bodies. Once I cut a few pieces off it is much easier to push it through the table saw for the small sides. I could always make another jig for the small sides if I wanted.

Comments

Post a Comment

Popular posts from this blog

Fixing Weber-type Charcoal Grill Legs

Do you have a charcoal grill? After awhile if you have moved it around do the legs come out? I have two of these grills and they both have this problem. But then again I did get both of them out of the trash! I suppose they were in the trash in the first place because their owner was tired of dealing with the legs coming out. The problem is that the legs are typically just crimped as you see below instead of firmly attached. Well, we are going to fix this! First, what you will need is a drill, a small-ish drill bit, and either 3 screws long enough to go all the way through the leg with nuts to go with them, or 6 rivets and a rivet gun. The drill bit naturally will be sized to fit the size of the screws or rivets. I like rivets because with screws there is a chance the nuts will come loose and then you are going to have wobbly legs again. Rivets are a permanent fix. So now that you have everything you need, drill a hole through the leg where it attaches to the grill. Make sure ...
Post a Comment
Read more

Shovel Handle Repair

Don't you hate when this happens? There you are digging in the garden and try to pry out a sapling stump and SNAP! If you can part with an old friend it is time to go buy a new shovel. If not (can you tell how much I have worn down the tip on this shovel?) it is time to replace the handle. Step one: Remove the Handle Notice where the rivet is installed through the handle.  Find the pre-formed end.  Look at the other side.  If it has been flattened much bigger than the hole through the shovel you will need to cut it off.  A Dremel tool with a cut-off wheel is the way to go.  Don't forget the safety glasses.  Now take a punch and hammer and knock the rivet through the shovel shaft.  Now you can knock the piece of the broken handle out of the shovel shaft. Step two: Fit and Drill the Hole in the New Handle But where to get your new handle?  I just read an article that mentioned the House Handle Company (http://househandle.com/index.ht...
Post a Comment
Read more

Making My Own Salt

My sister-in-law got a free rental weekend for a house in Nags Head. I had just read an Instructable on making sea salt and since we were headed to the beach it seemed like the perfect time to try it.  I found a few more articles and blogs on it and the basic process is Get sea water Filter out the sand and other junk Evaporate the water either by leaving in the sun or boiling or both Grind up to the consistency you want I got a nephew to got out in the surf with me and get a gallon milk jug and a couple two liter soda bottles of sea water.  First lesson learned - bring a bucket and wide mouth bottles or a funnel.  It is too hard to get the water in the surf to go through the little hole in these bottles and jugs.  It would have been better to have a bucket and then pour it in the jugs, filtering it along the way. When we got home I filtered it through some coffee filters which was a very slow process. I went back and reviewed the instructions and they all ...
Post a Comment
Read more