Skip to main content

Fixing Weber-type Charcoal Grill Legs

Do you have a charcoal grill? After awhile if you have moved it around do the legs come out? I have two of these grills and they both have this problem. But then again I did get both of them out of the trash! I suppose they were in the trash in the first place because their owner was tired of dealing with the legs coming out. The problem is that the legs are typically just crimped as you see below instead of firmly attached. Well, we are going to fix this!


First, what you will need is a drill, a small-ish drill bit, and either 3 screws long enough to go all the way through the leg with nuts to go with them, or 6 rivets and a rivet gun. The drill bit naturally will be sized to fit the size of the screws or rivets. I like rivets because with screws there is a chance the nuts will come loose and then you are going to have wobbly legs again. Rivets are a permanent fix.

So now that you have everything you need, drill a hole through the leg where it attaches to the grill. Make sure the leg is far enough into where it attaches that the hole will go through it also. The easiest location to start drilling is in the crimp. It provides a handy place to get the drill bit started. Make sure and drill all the way through.


If you are using screws and nuts push the screw through the hole, attach the nut, and tighten firmly. If using rivets you will need one for each side of the grill leg. Open the arms of the rivet gun, stick the long side of the rivet into the gun, push the rivet into the hole, and while keeping the rivet pushed firmly into the hole squeeze the arms together.


You may have to open the arms and squeeze shut a couple of times but eventually the rivet will tighten against the inside of the hole and the long shaft will break off. Do this again on the other side of the leg and there you go! I decided to do all the legs at once so I wouldn't have to worry about it again. There you have it! Nice firm legs!

Comments

Popular posts from this blog

Shovel Handle Repair

Don't you hate when this happens? There you are digging in the garden and try to pry out a sapling stump and SNAP! If you can part with an old friend it is time to go buy a new shovel. If not (can you tell how much I have worn down the tip on this shovel?) it is time to replace the handle. Step one: Remove the Handle Notice where the rivet is installed through the handle.  Find the pre-formed end.  Look at the other side.  If it has been flattened much bigger than the hole through the shovel you will need to cut it off.  A Dremel tool with a cut-off wheel is the way to go.  Don't forget the safety glasses.  Now take a punch and hammer and knock the rivet through the shovel shaft.  Now you can knock the piece of the broken handle out of the shovel shaft. Step two: Fit and Drill the Hole in the New Handle But where to get your new handle?  I just read an article that mentioned the House Handle Company (http://househandle.com/index.html), a family owned business in

Mark your own stemware

My wife and her sisters and cousins are going on girls weekend and to earn some husband points I decided to create some of these chalkboard paint stemware glasses I saw on Instructables.  http://www.instructables.com/id/ChalkBoard-Stemware/   I bought some cheap wine glasses at Wal-Mart and had some chalkboard paint left over from the wall of my basement shop. It is an easy process.  I wrapped a piece of electrical tape around the stem.  I used electrical tape because it is not as sticky as some other tape and so easier to get off once the painting is complete.  Also it is fairly thick so easier to find the end to unwrap it.  This makes it easier than something like tape you would use for wrapping paper. With the tape wrapped around the stem paint the bottom of the stem and base of the glass.  I used 3 coats.  One is not enough to cover well.  Two covered ok and was nice and smooth but I thought 3 would be more durable.  It will be interesting to see how well the paint holds up to