Skip to main content

Free Coolers

Want a free cooler to keep your drinks cold? Stop by your doctor's office.  I know you're saying, "Really my doctor?"  But when you think about it, it makes perfect sense.  Every family doctor gives a certain number of vaccinations.  Vaccines need to be kept cold.  Therefore, your doctor will have a constant supply of coolers coming into the office, especially in the fall when the flu vaccines arrive.  I have a supplier since my wife works in our doctor's office but I would think they would be happy to put these coolers to use instead of throwing them away.  I have seen two types.

 This one ships with dry ice and is not as thick but has more space inside.

This one ships with ice packs that fit into the space at the bottom and along the sides.  The bonus here is the ice packs.  They won't stand up as well as real blue ice but they are free so what the heck.  This one is also thicker but won't store as much, not quite a 6 pack with the ice packs in place.

Comments

Post a Comment

Popular posts from this blog

Fixing Weber-type Charcoal Grill Legs

Do you have a charcoal grill? After awhile if you have moved it around do the legs come out? I have two of these grills and they both have this problem. But then again I did get both of them out of the trash! I suppose they were in the trash in the first place because their owner was tired of dealing with the legs coming out. The problem is that the legs are typically just crimped as you see below instead of firmly attached. Well, we are going to fix this! First, what you will need is a drill, a small-ish drill bit, and either 3 screws long enough to go all the way through the leg with nuts to go with them, or 6 rivets and a rivet gun. The drill bit naturally will be sized to fit the size of the screws or rivets. I like rivets because with screws there is a chance the nuts will come loose and then you are going to have wobbly legs again. Rivets are a permanent fix. So now that you have everything you need, drill a hole through the leg where it attaches to the grill. Make sure ...
Post a Comment
Read more

Shovel Handle Repair

Don't you hate when this happens? There you are digging in the garden and try to pry out a sapling stump and SNAP! If you can part with an old friend it is time to go buy a new shovel. If not (can you tell how much I have worn down the tip on this shovel?) it is time to replace the handle. Step one: Remove the Handle Notice where the rivet is installed through the handle.  Find the pre-formed end.  Look at the other side.  If it has been flattened much bigger than the hole through the shovel you will need to cut it off.  A Dremel tool with a cut-off wheel is the way to go.  Don't forget the safety glasses.  Now take a punch and hammer and knock the rivet through the shovel shaft.  Now you can knock the piece of the broken handle out of the shovel shaft. Step two: Fit and Drill the Hole in the New Handle But where to get your new handle?  I just read an article that mentioned the House Handle Company (http://househandle.com/index.ht...
Post a Comment
Read more

Dinosaur Prints

I had the good fortune to take a step back in time 215 million years.  My brother-in-law and his son work for a construction company and were working near the Luck Stone quarry in Culpeper, VA. http://www.luckstone.com/content/culpeper Years ago as the quarry was mining stone dinosaur prints were found in a reddish colored layer of stone.  Some of the prints were cut out and now are displayed in the Smithsonian Institute.  As luck would have it we were allowed to not only go into the quarry to see the prints, but we were able to make several plaster casts of them. It was very cool to drive into the plant and see the equipment and then down into the quarry.  I don't often drive into a big pit!  The quarry is still active and water seeps into it so there are some pretty big water pumps that constantly pump it out.  After a lot of rain the pumps may not keep pace and the prints will be under water.  This is a view of the quarry from the bottom....
Post a Comment
Read more